Skip to content

Homeowner Guide · Permits & local rules

HVAC permits in St. George, Utah: when you need one and who issues it

“Do we need a permit for this?” is the question most St. George homeowners ask only after a quote arrives with a permit line on it — or, more often, after a cheaper quote arrives without one. This guide walks through what Utah’s adopted residential code actually says about mechanical work, which building office covers your address in Washington County, how the application works, and the handful of things this page deliberately leaves to the issuing office.

As of October 2026, a full air-conditioner, furnace, or heat-pump replacement in St. George, Utah is permitted work under the 2021 International Residential Code that Utah adopted statewide (Utah Code 15A-2-103, effective July 1, 2026): the code’s permit section covers replacing any mechanical system, and the short list of mechanical work it exempts — portable units, small self-contained units, minor part replacements — contains no central system. Inside city limits the permit comes from the City of St. George Building Department (61 S Main St, 435-627-4100) through its CityInspect portal; outside any city it is Washington County Community Development (435-301-7250).

Why a system replacement is permitted work here

Utah does not leave building codes to each city. The Legislature adopts the State Construction Code in Utah Code 15A-2-103, and the version effective July 1, 2026 (amended by H.B. 65 in the 2026 session) names the 2021 International Residential Code for houses and townhomes, with the 2024 International Mechanical Code applying to other buildings. The City of St. George’s Building Department page says the same thing in fewer words: design criteria must follow the currently adopted codes “pursuant to Utah’s House Bill 65 Construction Code Amendments.”

The permit question is answered in the IRC’s first chapter. Section R105.1 requires a permit before anyone sets out to “install, enlarge, alter, repair, remove, convert or replace any electrical, gas, mechanical or plumbing system” in a home. Section R105.2 then lists the work that is exempt, trade by trade. For mechanical work the whole list, as reproduced by building offices working from the 2021 edition, is:

  1. Portable heating appliances.
  2. Portable ventilation appliances.
  3. Portable cooling units.
  4. Steam, hot- or chilled-water piping within any heating or cooling equipment regulated by this code.
  5. Replacement of any minor part that does not alter approval of equipment or make such equipment unsafe.
  6. Portable evaporative coolers.
  7. Self-contained refrigeration systems containing 10 pounds (4.54 kg) or less of refrigerant or that are actuated by motors of 1 horsepower (746 W) or less.
  8. Portable-fuel-cell appliances that are not connected to a fixed piping system and are not interconnected to a power grid.

Utah’s statewide amendments to that section, in Utah Code 15A-3-202, edit the building-side exemptions — retaining walls, low decks, and an added exemption for storage conex boxes — and leave the mechanical list alone. Nothing in the model list or the Utah edits mentions a condenser, air handler, furnace, heat pump, or mini-split.

The practical line, then, runs between a service call and a system change. A tech diagnosing a unit that will not cool and swapping a failed part is doing AC repair in St. George, which the exempt list covers; a furnace that needs a new heat exchanger or blower assembly is still furnace repair on the same footing. The moment the condenser, air handler or furnace itself is being replaced, you are back under R105.1 and the permit applies.

Our reading of that list, stated as a reading: a like-for-like change-out of a central system is the replacement of a mechanical system with no exemption to point to, which is why it is permitted work. Neither the City of St. George’s permit pages nor the county’s say “HVAC replacements need a permit” in so many words — they point you to the adopted code and the application portal — so the right answer to a contractor’s “we don’t need a permit for this” is to call the issuing office yourself and describe the job. The code sets the rule; the local building official applies it to your house.

What the exempt list covers — and what it doesn’t

Read against the kinds of jobs St. George homeowners actually call about, the eight exemptions sort into three buckets.

Job Where it sits in the list
Window AC, portable AC, portable swamp cooler, space heater Listed as exempt (portable units; self-contained units at or under 10 lb of refrigerant or 1 hp).
Capacitor, contactor, fan motor, thermostat, or similar service-call part Likely covered by “replacement of any minor part that does not alter approval of equipment” — but what counts as minor is the building official’s call, and St. George publishes no list.
Condenser, air handler, evaporator coil, furnace, or packaged unit replacement Not on the list. A split system is field-connected rather than self-contained, and a full unit is not a minor part. Permitted work, by our reading.
Heat pump replacement or a gas-to-heat-pump conversion Not on the list; a conversion also changes the electrical load and may involve removing gas piping, each with its own trade rules.
Ductless mini-split installation Not on the list. The outdoor and indoor units are connected on site, so it is a split system; the 10-pound self-contained exemption is written for sealed, factory-charged units.

The “where it sits” column is this site’s reading of the model code text, not a statement from any Washington County building office. The office’s answer controls.

Who issues the permit: city or county

Washington County is a patchwork of city limits, and the building office that covers your system depends on which side of a line your lot sits on, not on your mailing address. Use the table, then confirm by phone.

Where the home is Who issues the permit Contact
St. George city limits City of St. George Building Department 61 S Main St, St. George — 435-627-4100, Mon–Fri 8 a.m.–5 p.m. Building permits are requested through the city’s CityInspect portal.
Washington City Washington City Building Department 111 North 100 East, Washington — (435) 656-6326.
Hurricane Hurricane City Building Department 147 N 870 W, Hurricane — 435-635-2811.
Ivins Ivins City Building Department (435) 634-9753.
Santa Clara Santa Clara City Building Department (435) 673-6712.
Unincorporated Washington County (Veyo, Central, Diamond Valley, Dammeron Valley, Gunlock, Apple Valley, Rockville, New Harmony) Washington County Community Development 111 East Tabernacle St., St. George — (435) 301-7250. The county accepts building-permit applications electronically only.

Office details as published by each office, verified October 30, 2026. The City of St. George’s Building Department page also lists its downloadable forms — among them a Building Fee Sheet, an “IRC Equipment and Duct Plan,” a “Final Inspection Checklist – Residential,” and a “Residential – Owner Builder” form — which is the closest thing the city publishes to an HVAC permit handout.

A Utah rule worth knowing: who may run the load calculation

One Utah-specific amendment matters more for an HVAC permit than anything in the exemption list. In Utah Code 15A-3-203, the state adds a new IRC section M1401.3.1 requiring that “an individual performing load calculations shall be qualified by completing HVAC training” from one of four routes: ACCA’s load calculation education, a recognized educational institution, an HVAC equipment manufacturer’s training, or another recognized industry certification. In plain terms, the Manual J-style sizing that decides whether your replacement is a 3-ton or a 4-ton system is supposed to be done by someone trained to do it — not read off the old unit’s nameplate.

That gives you a concrete question for any replacement bid: who ran the load calculation, what training qualifies them, and can you see the result? The AC installation page and the heat pump installation page cover why sizing matters so much in a St. George summer; the permit is where the state expects to see it done properly. If the bid is for a repair rather than a replacement, none of this applies — see what a St. George AC repair call involves instead.

How the process works, step by step

  1. Confirm which building office covers your address.

    City limits and county lines are not obvious in Washington County. If your tax notice says St. George, it is the City of St. George Building Department (435-627-4100). Washington City, Hurricane, Ivins, and Santa Clara each run their own building office, and addresses outside any city go to Washington County Community Development (435-301-7250).

  2. Put permit responsibility in the written scope.

    The normal arrangement is that the HVAC contractor applies for the permit under their own Utah DOPL license and the fee appears as a line in the bid. Get that in writing. A contractor who says a full system replacement needs no permit, or asks you to apply as the owner so their name stays off the record, has given you a reason to keep shopping.

  3. Have the equipment and load details ready before anyone applies.

    The City of St. George publishes an “IRC Equipment and Duct Plan” form among its building forms, and Utah’s code amendments require that whoever performs the load calculation be trained to do it. Ask for the equipment make, model, and capacity, the load calculation, and a note on any duct or electrical changes before the application goes in — the same items that belong in a complete bid.

  4. Apply through the right channel.

    The City of St. George takes building-permit requests through its CityInspect portal (one registration works across the Utah municipalities on that system); the county takes applications electronically only. Ask the office what its current fee is — St. George posts a Building Fee Sheet on the Building Department page — and whether a like-for-like replacement needs anything beyond the application.

  5. Schedule the inspection the office requires and keep the record.

    Ask the issuing office which inspections apply to an equipment replacement and when the contractor should request them. When the final passes, keep the permit number and the inspection result with your contract, warranty registration, and the load calculation; it is the document a future buyer, insurer, or warranty administrator will ask for.

When the system dies in July

The most common reason a St. George replacement happens without a permit is not a dishonest contractor; it is a triple-digit afternoon, a dead compressor, and a crew that can install tomorrow. The model residential code anticipates this: it carries an emergency-repairs provision for equipment replacements that cannot wait, and that provision is about when the application is filed, not whether it is filed at all. How the City of St. George or the county applies it to a mid-summer failure is a question for the issuing office — call before the crew arrives if you can, and ask the contractor to show you the application afterward if you can’t. “It was an emergency, so there’s no permit” is the clause being used as an excuse, not as written.

Permit, license, and insurance are three different checks

A permit says the work will be inspected. It says nothing about who is doing it. Those are separate checks, and all three belong in your file:

  • License. Utah’s Division of Professional Licensing (DOPL) licenses contractors, and its public lookup at secure.utah.gov shows status, expiration, classifications, and any disciplinary action; DOPL’s phone line is (801) 530-6628. Check that the licensed name matches the name on the bid and on the permit application. The contractor vetting guide walks through the lookup step by step. Utah Code 58-55-102(17) is also why this site reads the way it does — it treats anyone who advertises as a contractor as one, so St. George Air Repair researches local costs and companies and connects you with an independent licensed pro rather than performing any work itself.
  • Insurance. Ask for current certificates of general liability and workers’ compensation naming the business, and call the agent listed on them. Permits don’t verify coverage.
  • Manufacturer warranty registration. Most equipment warranties require registration within a window after installation, and some require a permitted, licensed installation to stay in force. The new-construction checklist covers the paperwork that goes with it.

What this page deliberately doesn’t tell you

A few things change by office and by job, and a guide that guesses at them does more harm than one that sends you to the source. The City of St. George’s permit fee comes from its published Building Fee Sheet, so ask the office or read the sheet rather than trusting a number on a flyer. The exact inspection sequence for an equipment replacement, the turnaround on an application, whether a particular repair part will be treated as “minor,” and how an emergency replacement is handled are all calls the issuing office makes. HOA architectural approval — common in St. George’s planned communities for the placement or screening of an outdoor unit — is a private rule layered on top of the permit, and the HOA’s own documents are the only source for it. La Verkin and Toquerville homeowners should contact their own city office; those building departments’ details are not reproduced here.

Want a pro who pulls the permit for you?

Most reputable local HVAC companies handle the permit as part of a replacement and show it as a line in the bid. If you would rather not start from a search page, request quotes below and we’ll connect you with an independent local HVAC contractor who serves your address — then run the license lookup and the permit question past them yourself. For the numbers to compare bids against, the HVAC replacement cost guide and the AC repair cost guide are the place to start.

Sources and methodology

Sources, read October 30, 2026. Utah Code 15A-2-103 (adopted code editions) and Title 15A, Chapter 3, Part 2 — sections 15A-3-202 (amendments to IRC chapters 1–5, including R105.2) and 15A-3-203 (amendments to the IRC mechanical chapters, including the new M1401.3.1 load-calculation qualification) — on le.utah.gov; 2021 International Residential Code sections R105.1 and R105.2 as reproduced in building-department handouts published by the City of Springville, Utah and Grant County, Washington (two reproductions, compared item by item and found identical); the City of St. George Building Department and Permits & Inspections pages (sgcityutah.gov); the Washington County Community Development page (washco.utah.gov); and the building-department contacts published by Washington City, Hurricane, Ivins, and Santa Clara.

What was and wasn’t confirmed. The adopted code editions, the Utah amendments, the model exemption list, and the office contacts above were each read from the issuing body’s own published text. The conclusion that a central-system replacement is permitted work is this site’s reading of that text — no St. George or county page was found stating it in so many words. Fees, inspection sequences, and how a given office treats a specific repair were not confirmed and are not stated.

What this guide is, and isn’t. Homeowner-education content, not legal advice. Codes and office details change — confirm with the issuing office before relying on any of this for a specific project.

Published October 30, 2026.

FAQ

Common questions

Do I need a permit to replace my AC in St. George, Utah?

As of October 2026, replacing a central AC, furnace, or heat pump in St. George falls under the building-permit rules of the 2021 International Residential Code that Utah adopted statewide, whose permit section covers replacing any mechanical system and whose short list of permit-exempt mechanical work names only portable units, small self-contained units, and minor part replacements. The City of St. George Building Department (435-627-4100) issues permits inside city limits through its CityInspect portal; confirm your specific job with that office before work starts.

Who issues HVAC permits in St. George — the city or Washington County?

Inside St. George city limits it is the City of St. George Building Department at 61 S Main St (435-627-4100). Washington County Community Development (435-301-7250) handles addresses outside any city, such as Veyo, Central, Dammeron Valley, and Apple Valley, and accepts applications electronically only. Washington City, Hurricane, Ivins, and Santa Clara each have their own building department.

Does an AC repair need a permit in St. George?

The model code exempts “replacement of any minor part that does not alter approval of equipment or make such equipment unsafe,” so a service call that swaps a capacitor or a contactor is normally treated differently from replacing the condenser or air handler. Where the line falls for a given part is the building official’s call, not the contractor’s, and St. George does not publish a list, so ask the Building Department at 435-627-4100 if a repair bid is large enough to make you wonder.

Is a window AC unit or a portable cooler exempt from a permit?

Yes, under the model code’s mechanical exemptions: portable cooling units, portable evaporative coolers, and self-contained refrigeration systems holding 10 pounds or less of refrigerant or driven by motors of 1 horsepower or less are listed as work that does not need a permit. A split system — a condenser outside connected by refrigerant lines to a coil inside, including a ductless mini-split — is not self-contained, so that exemption is not the one to rely on for it.

How much does an HVAC permit cost in St. George?

The City of St. George publishes its current fees in a Building Fee Sheet on the Building Department page, and the fee depends on the job, so this page does not quote a figure. Ask the office or read the sheet, and expect the contractor’s bid to show the permit as its own line rather than folding it into equipment.

Who should pull the permit — me or the HVAC company?

The contractor, under their own Utah DOPL license, is the normal and safer answer: the permit record then shows who did the work, which matters if a warranty or insurance question comes up later. St. George does publish a Residential Owner-Builder form, but a contractor asking you to pull the permit as the owner is asking you to put your name on their work.

My AC died in July — can the replacement wait for a permit?

The model residential code has an emergency-repairs provision for equipment replacements that cannot wait, which deals with the timing of the application rather than waiving it, and the issuing office decides how it applies to a mid-summer failure. Ask the Building Department how it handles emergency replacements before the work starts; a contractor who treats “it was an emergency” as a reason to never file is using the clause as an excuse.

What happens if an HVAC system was replaced without a permit?

The practical consequences show up later: no inspection record for a buyer, insurer, or manufacturer warranty claim, and the possibility that the building office requires the work to be permitted and inspected after the fact. If you are buying a St. George home with a recent system, ask for the permit number and the final-inspection result and check it against the issuing office’s records.

Free · No obligation

Get matched with a local pro who handles the permit

Tell us what you need and we’ll connect you with an independent local HVAC contractor serving St. George and Washington County. No obligation.

When you submit, your request goes to the independent local HVAC provider matched to it, so they can contact you about it. See our Privacy Policy.

More guides: all St. George HVAC guides, or head back to the St. George Air Repair home page.

Call Now Get Free Quote